Products

How to find out exactly which mobile tower your phone is connected to.

19 Oct 2019
phone cell tower1

For complicated or large repeater installations, it is useful to know precisely which cell tower your phone is connected to. This will help you understand the nature of the mobile signal inside and around the building. It will also help you in orientating the outdoor antenna.

Some apps show you the direction of the tower with a compass needle.  Some other apps make an estimation of where the tower is and show this location on a map. Both options produce results that are either inaccurate or false, and therefore cannot be trusted.

The method I will explain in this article is a little time consuming,  but it will give you accurate information which is invaluable for more professional installations.

Equipment:

  • 3X Samsung phones with a SIM for each operator.
  • Notebook

Samsung Galaxy phones are the best phones with which to gather cell tower information.

With this phone you can get:

  • Signal Power
  • Band number (frequency)
  • CID/TAC: (Cell ID)
  • Service (GSM,H+, 4G etc…)

The CID, Cell ID, uniquely identifies the cell tower. This is very important information.

Install the app, Network Cell Info Lite (NCIL) on all 3 Samsung phones:

Here is an example of NCIL on my Vodafone Samsung phone:

  • Signal Power: -111dBm
  • Band: 20 (800MHz)
  • CID/TAC: 37100-81937409
  • Service: 4G

 

Screenshot_20181009-170025_Network Cell Info Lite

Hot tip!

In a Samsung phone, you can always access this raw data by typing *#0011# into the keypad. From here you can get  all the data above without installing the app NCIL.

 

Step #1 – Drive to the first nearby tower.

Drive to the nearest cell tower from your building. You can often see this mobile tower from the roof of the building. In some countries, there are government maps showing you precisely where the cell towers are.

France:

https://www.cartoradio.fr/index.html#/

Spain:

https://geoportal.minetur.gob.es/VCTEL/vcne.do

Ireland:

https://siteviewer.comreg.ie/

If you are not in one of these countries, you may have to rely on spotting these cell  tower from the roof of the building.

So, either walk or drive to this first tower. You do not need to go right to the base of this tower. It’s OK to be 50-100 meters away from it.  When you get there, take out your 3 phones and notepad and begin the first test.

Test #1 – The First Cell Tower

Using NCIL take a note of the:

  • Signal Power
  • Band number(frequency)
  • CID (Cell ID)
  • Service(GSM,H+, 4G etc…)

..for each of your phones.

Also take a note on a map of the location.

Example:

Orange:

B3, -76dBm, 4G, 4001-4566634

O2:

B3, -72dBm, 4G, 3441-47665634

Vodafone:

B1, -77dBm, 3G, 3225-45634

Test #2 – Do the same test for all cell towers around the building.

Then, go to all the other cell towers near the building, and collect the same data.

Mark all tower locations on a map.

Here is an example of one such building and the locations of the nearby towers. The circles denote each of the mobile operators. You will find that often times the one tower will host base stations of several operators.  In the map below, we went to all the 4 towers and gathered data from all operators on those towers.

The little colored boxes on each tower denote the actual operators on that tower.

 

towers around building map

 

Conclusion:

You only need to collect data off the nearby towers in any direction around the building. This can range from 2-3 tower in rural locations, to 5 or more in towns/cities.

After collecting all information from the towers in the area, you  can now return to your building and do the same test again on the roof of the building.

Comparing results.

Now you can compare the CID/TAC information on the roof to the data you have just collected in your notepad, and you should get a match.

You now know precisely which tower your phones are connecting to from the roof of the building.

For your installation, you should point the outdoor Yagi antenna in this direction, as a general rule.

I also advise you test inside the building to see if there is “natural signal* entering the building, and now you will know which exact tower is sending strong  signal into  the building naturally.

Again, if this is the case, point the Yagi at this tower.

*”Natural signal” is signal you measure inside the building that is present all the time, when there is no repeater installed.

Ideally, we prefer not  to see any natural signal in the building. This is often the case in highly insulated  modern buildings.

However, older buildings usually have some natural signal and we should  be aware of this.

 

 

 

 

You may also like:

    Parabolic Dish in the City - Multiple Base Station Issue.

    13th November 2019
    In this article, I will discuss a problem that can arise with repeater installations in cities. This problem can arise when you install the outdoor antenna on a very high building that has views over the city. If the building is very high, from the roof, the outdoor antenna can see across the city. It [...]
    read more

    How to best use Network Cell Info Lite

    31st October 2019
    Network Cell Info Lite, (NCIL) is an android app that can tell you alot about your phones cellular connection. To get the most valuable information , like band information (frequency) and CELL ID’s, this app should be installed on any Samsung Galaxy phone. Only Samsung phones reveal this invaluable data. I personally use an S8 [...]
    read more

    Cell towers - What are CID's and LAC's

    26th October 2019
    Whenever you make a call or use mobile data, your phones is connecting to one specific cell tower. To be more precise, your phone is connecting to one of those sector antennas on a particular mast. See image above. Each of these sector antennas has a unique identification. A CID – Cell ID, and a [...]
    read more